Warranty: | After Shipping 14 Month |
---|---|
Shaping Mode: | Injection Mould |
Surface Finish Process: | Electroplating |
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
Ejection Retraction Key |
When the ejector leaves the backward limit switch, press this key to retract the ejector back to the backward limit switch. |
Ejection Advance Key |
The ejection advance is activated at the mold opening end position and the cores are all retracted. If the ejection count is set and the limit switch of advance/retraction is normal, pressing this key will execute ejection advance continuously according to the ejection count. |
Air Blast A Key |
In Manual mode, press this key to execute air blast of A group according to the pre-set time and position. |
Air Blast B Key |
In Manual mode, press this key to execute air blast of B group according to the pre-set time and position. |
Robot | When the robot function is selected to "Use", press this key to activate the robot. But make sure at the robot's pre-set activation position firstly. |
Lubrication | In the manual mode, press this key to open the lubrication bump. |
Core A In /Core A Out |
Core A function option, press core in or core out key in the manual mode, the core A will move in/out. |
Core B In /Core B Out |
Core B function option, press core in or core out key in the manual mode, the core B will move in/out. |
Core C In/ Core C Out |
Core C function option, press core in or core out key in the manual mode, the core C will move in/out. |
Pin Advance | When the machine is equipped with positioning valve, press this key at the rotary end position to activate the pin forward movement. |
Pin Retraction | When the machine is equipped with positioning valve, press this key at the rotary end position to activate the pin backward movement. |
Rotate | In case of 360 degrees, press this key in Manual mode, the disk will rotate by a station. (For rotary machine only) |
Table Left/ Table Right |
After all conditions below are met: Opening mold is at the end position, the ejector retracts to the right place and the pin locates at the backward end position. Press this key, the table will rotate to the left or right. (For rotary machine only) |
Injection |
In the manual mode or Coarse Adjustment mode, when the barrel temperature is within the deviation range, press this key to execute injection and execute hold pressure. |
Suck-Back |
In the manual mode or Coarse Adjustment mode, when the barrel temperature is within the deviation range, press this key to execute suck-back. |
Charge |
In the manual mode or Coarse Adjustment mode, when the barrel temperature is within the deviation range, press this key to execute charge, and please press this key once more to stop. |
Auto Purge | In the manual mode, if the operator is willing to clean up the defective material in the barrel, press this key to execute Auto Purge according to the pre-set cleaning count and time in Purge page. |
Nozzle Advance |
In the manual mode or Coarse Adjustment mode, press this key to execute nozzle advance. |
Nozzle Retraction |
In the manual mode or Coarse Adjustment mode, press this key to execute the nozzle retraction. |
Nozzle Move Down |
In Manual mode, press this key to lower the nozzle to the appropriate position, which is used to adjust the distance between the spure gate and mold. |
Nozzle Move Up |
In Manual mode, press this key to raise the nozzle to the appropriate position, which is used to adjust the distance between the spure gate and mold. |
Motor On/Off |
In the manual mode or Coarse Adjustment mode ,press this key to turn on the hydraulic pump motor and the motor icon will appear on the screen. Press once again to turn off the motor and the motor icon will disappear. (This key is invalid in Auto mode) |
Heater On/Off |
In the manual mode or Coarse Adjustment mode ,the barrel will start heating and the heater icon will appear on the screen. Press once again, heating will stop and the heater icon will disappear. (This key is invalid in Auto mode) |